series am10cw-fz 10 watt | dc-dc converter www.aimtec.com tel: +1 514 620 2722 toll free: + 1 888 9 aimtec (924 6832) f 051e r13 1 of 3 north america only picture coming soon features: ? wide 4:1 input voltage range ? ? high efficiency up to 88% ? ? remote on/off ? ? standard 1?x1? package ? models single output model input voltage (v) output voltage (v) output current max (ma) max capacitive load(uf) efficiency (%) AM10CW-2403S-FZ 9-36 3.3 2200 3300 82 am10cw-2405s-fz 9-36 5 2000 2200 85 am10cw-2412s-fz 9-36 12 830 680 88 am10cw-2415s-fz 9-36 15 660 330 88 am10cw-2424s-fz 9-36 24 410 100 87 am10cw-4803s-fz 18-75 3.3 2200 3300 80 am10cw-4805s-fz 18-75 5 2000 2200 84 am10cw-4812s-fz 18-75 12 830 680 87 am10cw-4815s-fz 18-75 15 660 330 87 am10cw-4824s-fz 18-75 24 410 100 87 models dual output model input voltage (v) output voltage (v) output current max (ma) max capacitive load(uf) efficiency (%) am10cw-2405d-fz 9-36 5 1000 1000 85 am10cw-2412d-fz 9-36 12 410 470 88 am10cw-2415d-fz 9-36 15 330 220 87 am10cw-4805d-fz 18-75 5 1000 1000 84 am10cw-4812d-fz 18-75 12 410 470 87 am10cw-4815d-fz 18-75 15 330 220 87 note: all specifications in this datasheet are measured at an ambient temperature of 25c, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. input specifications parameters nominal typical maximum units voltage range 24 9-36 vdc 48 18-75 filter pi start up time 77 ms absolute ma ximum rating 24 50 vdc 48 100 peak input voltage time 100 ms on/off control on ?open or 3.5 to 12v/<0.2ma off ?short to pin 2 (-vin) or 0 to 0.7v idle input current at off state 12 ma input reflected current 62 ma p-p transient response settling time 50% load step change 550 s transient response deviation di/dt=0.8a/s 5 % 3.3vou 6
series am10cw-fz 10 watt | dc-dc converter www.aimtec.com tel: +1 514 620 2722 toll free: + 1 888 9 aimtec (924 6832) f 051e r13 2 of 3 north america only isolation specifications parameters conditions typical maximum units tested i/o voltage 1500 vdc resistance 500vdc >1000 mohm capacitance 1100 pf output specifications parameters conditions typical maximum units voltage accuracy 1 % over voltage protection 3.3 vout 5 vout 12 vout 15 vout 24 vout 3.9 6.2 15 18 27 v short circuit protection continuous short circuit restart auto-recovery line voltage regulation ll to hl at full load 1 % of vin load voltage regulation (single) 0% to full load 1 % load voltage regulation (dual) balanced load 0.5 % unbalanced load 25 to 100% load 5 temperature coefficient 0.02 %/ o c ripple & noise 20mhz bandwidth 80 mv p-p general specifications parameters conditions typical maximum units switching frequency 100% load 330khz khz operating temperature with derating above 60c -40 to +85 o c storage temperature -55 to +125 o c maximum case temperature 105 o c cooling natural convection humidity 95 % rh case material nickel-coated copper weight 17.4 g dimensions (l x w x h) 1 x 1 x 0.4 inches 25.4 x 25.4 x 10.2 mm mtbf >1,580,000 hrs (mil-hdbk -217f , ground benign, t=+25c) pin out specifications pin single dual 1 +v input +v input 2 -v input -v input 3 on/off control on/off control 4 +v output +v output 5 no pin common 6 -v output -v output
series am10cw-fz 10 watt | dc-dc converter www.aimtec.com tel: +1 514 620 2722 toll free: + 1 888 9 aimtec (924 6832) f 051e r13 3 of 3 north america only dimensions notes: all dimensions are typical in millimeters (inches). pin pitch tolerance 0.35 (0.014) case tolerance 0.50 (0.02) derating -40 -20 0204060 80 100 100 80 60 40 20 0 safe operating area output power (%) 85 ambient temperature o c free air convection 30 60 o c note: 1. datasheets are updated as needed and as such, specifications ar e subject to change without notic e. once printed or downloaded , datasheets are no longer controlled by aimtec; refer to www.aimtec.com for the most current product specifications. 2. product labels shown, including safety agency cert ifications on labels, may vary based on the date manufactured. 3. mechanical drawings and specifications are for reference only. 4 . all specifications are measured at an am bient temperature of 25c, humidity<75%, nominal input voltage and at rated output load unless otherwise specifie d. 5 . aimtec may not have conducted dest ructive testing or chemical analysis on all internal components and chemicals at the time of publishing this document. cas numbers and other limited information are considered proprietary an d may not be available for release. 6. this product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control sys tems or other such applications which necessitate specific safety and regulatory standards other the ones listed in this datasheet . 7. warranty is in accordance with aimtec?s st andard terms of sale available at www.aimtec.com . 25.40 (1.00) 2.54 (0.10) 20 .32 (0.80) 2.54 (0.10) 10 .16 (0.40) 5.08 (0.20) 7.62 (0.30) 2.54 (0.10) 10 .16 (0.40) 10 .16 (0.40) 25.40 (1.00) 9.90 (0.39) printed face 1.00 (0.39) top view side view 2.54 (0.10) 1 +v in put 2 -v inpu t ctrl 3 4 56 +v output -v outp ut bottom view
|
